| Model |
Unit |
JSSCD-810NC |
JSSCD-1310 |
JSSCD-1610 |
JSSCD-2610 |
| Mainframe dimensions (L*W*H) |
mm |
4100*2000*2500 |
7100*5050*2360 |
7400*5600*2460 |
6500*4900*2500 |
| Cutting range |
mm |
50-810 |
850-1310 |
850-1610 |
1800-2610 |
| Cutting thickness |
mm |
20-100 |
20-120 |
20-120 |
20-120 |
| Saw blade size |
|
425*2.3*3.0*φ50 |
425*2.3*3.0*φ50 |
425*2.3*3.0*φ50 |
425*2.3*3.0*φ50 |
| Pin holes and hole diameters |
|
4*φ16*90 |
4*φ16*90 |
4*φ16*90 |
4*φ16*90 |
| Spindle motor power |
kw |
15(4P) |
18.5(4P) |
18.5(4P) |
18.5(4P) |
| Spindle speed |
rpm |
20-120 |
20-120 |
20-120 |
20-120 |
| Cut off feed mode |
|
AC servo motor + gantry upper blade |
AC servo motor + gantry upper blade |
AC servo motor + gantry upper blade |
AC servo motor + gantry upper blade |
| Feed servo motor power |
kw |
3.6 |
3.6 |
3.6 |
3.6 |
| Main clamp method |
|
Hydraulic Type Or Horizontal ,Vertical type |
Hydraulic Type Or Horizontal ,Vertical type |
Hydraulic Type Or Horizontal ,Vertical type |
Hydraulic Type Or Horizontal ,Vertical type |
| Saw blade debris removal device |
|
Passive/Active circular wire brush (optional) |
Passive/Active circular wire brush (optional) |
Passive/Active circular wire brush (optional) |
Passive/Active circular wire brush (optional) |
| Gear backlash compensation device |
|
Hollowexternal rotating magnetic powder brake |
Hollowexternal rotating magnetic powder brake |
Hollowexternal rotating magnetic powder brake |
Hollowexternal rotating magnetic powder brake |
| Feeding drive mode |
|
AC servo motor & ball screw |
AC servo motor & ball screw |
AC servo motor & ball screw |
AC servo motor & ball screw |
| Feeding servo motor power |
kw |
2 |
2 |
2 |
2 |
| Feeding clamp method |
|
Hydraulic type/ Horizontal clamping |
Hydraulic type/ Horizontal clamping |
Hydraulic type/ Horizontal clamping |
Hydraulic type/ Horizontal clamping |
| Material removal length at the front |
mm |
10-99 |
10-99 |
10-99 |
10-99 |
| Residual material length at the rear end |
|
95&a(a represents the length less than one cut-off workpiece) |
95&a(a represents the length less than one cut-off workpiece) |
95&a(a represents the length less than one cut-off workpiece) |
95&a(a represents the length less than one cut-off workpiece) |
| Single feeding length (repeatable feeding) |
mm |
6-590 |
6-590 |
6-590 |
6-590 |
| Hydraulic drive motor power |
kw |
2.25 |
2.25 |
2.25 |
2.25 |
| Rated pressure of the hydraulic system |
MPA |
5.5 |
5.5 |
5.5 |
5.5 |
| Hydraulic oil capacity |
L |
100 |
100 |
150 |
200 |
| Self-lubricating oil system |
|
Timed and quantitative forced oil supply |
Timed and quantitative forced oil supply |
Timed and quantitative forced oil supply |
Timed and quantitative forced oil supply |
| Micro-lubrication system for cutting |
|
Quasi-dry intermittent oil supply |
Quasi-dry intermittent oil supply |
Quasi-dry intermittent oil supply |
Quasi-dry intermittent oil supply |
| Blade swing anti-vibration device |
|
Tungsten carbide parallel block |
Tungsten carbide parallel block |
Tungsten carbide parallel block |
Tungsten carbide parallel block |
